Shotgun Function Testing

Shotgun Function Testing (Part 2)
By Ben Kurata

Wilson Combat Border Patrol Shotgun

*This is the second entry in a 2-part series on Long Gun Function Testing. Part 1 can be found here.

Action Target

Provo, Utah --(Ammoland.com)- In a previous article, I covered function testing the AR-15 / M4 patrol rifle and variants.

Now, let’s turn to that old standby of the police arsenal, the 12 gauge pump shotgun. It’s a common misconception that the 12 gauge pump shotgun is maintenance free. Certainly, the majority of shotguns I’ve seen were evidence of this misguided belief.

The police shotgun has to be routinely cleaned, lubricated and function tested the same as any other duty weapon. One area that most shooters overlook when cleaning and lubricating the police shotgun is the magazine tube. The tube is made of steel, and the magazine spring and shell follower are made of steel. (If the shell follower in your shotgun is a thin plastic cap, discard it and get the steel one. If the plastic cap breaks inside the magazine tube, you’ll have to put the shotgun on to the workbench to get it to work again.)

When the shotgun is carried in “cruiser carry” mode, the magazine spring is compressed against the interior of the magazine tube. Let some moisture get into the magazine tube, and corrosion of magazine spring can occur.

Whenever I disassemble, clean, lubricate and function test my shotgun, I push a bore brush and patches wet with solvent through the magazine tube until the patches come out clean. I finish up with a clean patch moistened with lubricant followed by a clean, dry patch. A wipe down of the magazine spring with some lubricant completes the maintenance on the magazine tube.

Function Testing of the Pump Shotgun:

Make certain that there is no live ammunition in the magazine tube or chamber. With the bolt back, a quick physical check through the loading port by touching the magazine follower and the empty chamber gets the task done.
Pump the fore end all the way forward. Try to pull the fore end back. The fore end and bolt should remain locked forward.
Put the safety on “Safe”. Press the trigger, hard. Nothing should happen.
Point the muzzle in a safe direction and press the trigger. You should feel / hear a normal hammer fall. Keep the trigger depressed.
Disengage the safety and with the trigger depressed, roll the shotgun sideways so you can look through the ejection port. Slowly work the fore end all the way back and then forward. You should see the shell lifter rise up when you start the fore end forward. Continue to push the fore end all the way forward while keeping the trigger depressed.
Slowly let the trigger forward until you feel and hear the disconnector reset. It won’t take much forward motion of the trigger, and the reset will be subtle. The reset on my personal Remington 870 feels about the same as my 1911A1 Colt. Yes, all modern pump shotguns since the model 1897 Winchester have disconnectors.
Press the trigger again. Your function test is now complete.

Function Testing the Police Semiautomatic Shotgun:

Make certain that there is no live ammunition in the magazine tube or chamber. With the bolt back, a quick physical check through the loading port or the ejection port by touching the magazine follower and the empty chamber gets the task done.
Let the bolt go forward by pressing the bolt release button. The bolt should move forward sharply and lock into the rear of the barrel.
Point the muzzle in a safe direction and put the safety on “Safe”. Press the trigger, hard. Nothing should happen.
Point the muzzle in a safe direction and press the trigger. You should feel / hear a normal hammer fall. Keep the trigger depressed.
Disengage the safety and with the trigger depressed, roll the shotgun sideways so you can look through the ejection port. Slowly pull the charging handle to the rear with your non-dominant hand and ease it slowly forward. As the bolt starts forward, you should see the shell lifter rise up. Work the charging handle back and forth a few times. You shouldn’t feel any unusual binding, just slight resistance when the bolt unlocks and a slight “bump” as the bolt body passes over the hammer.
Pull the charging handle all the way back and let it fly forward.
Slowly let the trigger forward until you hear and feel the disconnector reset. Again, this won’t take much forward motion of the trigger and is subtle (compared to the disconnector reset on say, an AR-15).
Press the trigger again. Your function test is now complete.

*This is the second entry in a 2-part series on Long Gun Function Testing. Part 1 can be found here.

About Action Targets:
Action Target is a privately owned business headquartered about 40 miles south of Salt Lake City in Provo, Utah. For the last 20 plus years, Action Target has been the dominant force in shooting range equipment design and manufacturing for law enforcement, military, and commercial ranges around the world. We are proud of our commitment to deliver advanced firearms training products that help prepare our men and women in uniform for the heroic job of defending our safety and our freedom. Visit: www.actiontarget.com