C Products Defense Mags 100,000 Rounds Test – Zero Failures

C Products Defense Magazines
C Products Defense Magazines
C Products Defense Logo
C Products Defense

USA – -(Ammoland.com)- C Products Defense Magazines are officially the most thoroughly tested magazine on the planet with over 100,000 documented rounds by a major firearm manufacturer with zero failures and zero parts replacements, exceeding all government specifications and operating flawlessly in all extreme environments.

C Products Defense recently competed with other magazines for an OEM contract with a major firearm manufacturer and were the only magazine with zero failures with over 100,000 rounds of testing.

“We were surprised by the extensiveness of the testing but not surprised by the results,” says C Products Defense armorer and sales manager, Bill Rogers. “Our magazines will not jam,” continues Rogers, “due to four main factors:

  • A Metal Magazine
  • A Caliber-Specific Geometry
  • A Proprietary Coating
  • A Specially Engineered Anti-Tilt Follower

Metal vs. Polymer

Polymer magazines, which have been banned by the United States military since May of 2012, are hygroscopic in nature, in other words, they have a strong affinity to attract moisture and will absorb moisture onto their molecular structure when exposed to the ambient air. This moisture, within the polymer, reacts constantly with the surrounding environment.

C Products Defense 7.62 X 39 10 Round Magazine
C Products Defense 7.62 X 39 10 Round Magazine

At the molecular level, water vapor, surrounding a hygroscopic polymer element is absorbed into the polymer. As the vapor pressure within the polymer increases to equal the vapor pressure surrounding the polymer, equilibrium occurs. This is referred to as, polymer moisture equilibrium or PME.

When an environment of hot, dry air surrounds a wet hygroscopic polymer element, the vapor pressure surrounding the polymer is lower than the vapor pressure within the polymer. Consequently, the moisture within the polymer begins to migrate toward the area of low vapor pressure outside the polymer.

Expose the polymer to a hot, dry atmosphere for a sufficient period of time, the polymer eventually reaches moisture equilibrium with the surrounding dry conditions. In other words, the polymer becomes dry and deformation will occur, changing its shape from its original design.

“The opposite is also true,” adds Rogers. “When the moisture within the polymer is cooled sufficiently, say below the freezing point, the moisture will actually freeze and the polymer will crack as happened and reported by the Chicago Swat Team this past winter. Officer Frank Gaber, who is the Armorer and Instructor for the Chicago Swat, reported that this past winter they had multiple reports of a polymer mag shattering (and bullets scattering) when they were dropped on a hard surface. This was actually due to the moisture within the polymer and when that moisture froze it caused the magazines to shatter.”

Consequently, the only magazines that the Chicago SWAT Team will use are C Products Defense magazines.

“Finally, we all know how moisture attracts dirt and dust and gives it a place to collect. In a firearm, dust and dirt gives way to a corrosive cocktail which will lead to excess wear and eventually early failure of the firearm.”

“Aluminum or stainless steel do not have an affinity for moisture and any moisture (through condensation or immersion) remains on the surface and is easily removed by evaporation or just wiping it down. No moisture is absorbed into the metal. And our proprietary coating which bonds at the molecular level and will never wear off, decreases the coefficient of friction and increases the lubricity which means that even if you are using the dirtiest ammunition on the planet, our magazines will not jam because there is no dirt and dust accumulation or attraction.”

“We’re very excited to have the most tested magazine on the planet with zero failures,” adds Rogers. “But we’re not sitting still, we have some exciting products in the pipeline which will be released later this year.”

C Products Defense Mags 100,000 Rounds Test - Zero Failures
C Products Defense Mags 100,000 Rounds Test – Zero Failures

About C Products Defense
C Products Defense is proud to be a U.S. based manufacturing company with over 50 years of combined experience in the firearms industry. We provide outstanding products for the military, law enforcement agencies, and firearm manufacturers but it doesn’t stop there. In order to keep meeting the changing requirements of our customers, CPD is continuously developing new products, and your suggestions are always welcome.

For more information on C Products Defense, please visit online at www.CPDmags.com.

1 Comment
Most Voted
Newest Oldest
Inline Feedbacks
View all comments
Barry M

I just wanna say this Magazine is Simply made Better Than Any Pmag..or Any other out Yhere !!!…. .! I was a Dedicated pmag man , but Noticed Immediately The Anti tilt Follower, I started investigating And Seen many many corners cut By Pmag .in there Design , I couldnt Believe what I was Seeing ….It was true , see for yourself, and there cheaper and made in the Usa …needless to say Im putting the pmags up for sale …I stumbled upon these mags when they came free with a Del ton AR15…Also made in usa with a lifetime… Read more »